testing the Cool Bit OSC-s for seeming L.e.d.spk. measurement

actually for OSC frequency measurement ... anyway

made a real test with hybrid vid.amp ~ dif.amp circuit but it didn't work reliably enough to be sure of the frequency (so i hope one of the next actually'll 2 the 3-ck before i need to set up some opampsh¡t)

1-st Std. (modified)

2-nd -- an emulated tunnel diode (modified)

---

update 2017.04.25 :: some opampsh¡t

---

[Eop]

HiFq Flasher revisited + SCR alternate

somewhat unusual LED-driver that i doubt will startup with 2N2222-s but might with single MJE13005 or with it's higher frequency v.

the following appears to be an in series (or in parallel) self-powering/-delimiting supply for power control -- a concept / feature-research design for . . . !!!

PS! -- it quite likely is not secure to build and use as shown e.g. one must realize the principles and shortcomings here , also extensive additional testing is needed to verify such as secure or not -- there were studied a special situations where the supply failed to lock up / delimit itself -- i haven't collected enough data on it yet !!!

---

[Eop]

Shockley Diode , Tunnel diode , SCS SCR - BJT alternates study

Shockley ::

Dev. :

Low Voltage Neon Tube Replacement for ring counter:

Optimizing Hysteresis Curve:

Voltage pass over detector::

the following circuit may be possible to dev. further to a low speed tunnel diode variant:

Shockley to SCR ::

SCR RAM cell:

SCR Binary Counter:

---

[EoP]

Low Voltage SCS Counter Experiment

. . . integrated the www resource (poor) with my past experimental Lo voltage SCS designs . . . to just about get a working theoretical "New One" -- the 2 things marked on a fig. tell us that such is not likely to succeed in practice ...

actually i was playing around with oscillator designs the SCS-s in mind -- the cool feature about this thing (scs) is like some modern GHz MOSFET counters also DRAM e.c. those things can be designed to use practically no current and then shift 'em to another state by a narrow pulse

so, while i achieved my next osc. i studied in parallel an old electronics book - came across with ?? neg. triggered ring counter ?? thought to investigate it , improved the "CLK" shown in book for 1.2V supply . . .

after no success with the counter i actually realized that the TYPE of a counter i'm using for my improved CLK uses the pos. going pulse . . . yo!

. . . usually i finish what i started so the 1.fig. of this post actually shows the finished 1.2V design

for incase i'd ever need such in practice - i converted it to higher vtg. v. where the SCS is more likely to operate in realistic supply range . . . -- the ▼ "signal forward continuity test" ▼

► what's it made of ▼▼

it's tricky to get the signal out from low power "oscillators" -- here's one possibility :

PS! -- as the simulation in Spice may perform up to 1000x better than the actual circuit in real then it's not recommended to rush blindly building large systems composing them from the unknown / not studied designs
-- it's about 1 to 1k x that averages to ²√(1·1000) = 30dB = apx. 32x in general (more usually it's about 10x - maybe coz i ban the designs that perform worse ...) -- to get this right -- say if your 10Vdc PSU design has a simulation peak error ±24µV then in real device the appropriate value is to be expected ±24mV -- so it's 1000x change in relative error . . . as ±24mV/10V is ±0.24% then the common understanding of 1k x performance drop can't be grasped right without knowing the preceesding

 -- it's also why i don't build much of the stuff -- coz it takes testing separate stages . . . 1 by 1 . . . also verifying similar (same circuit) stages built from real components (with deviating parameters) that usually ends up in narrowing the operating ranges . . . without all possible fancy lab equipment in hand it takes more time than there is available . . .

... e.g. if you find such (SCS counter) interesting you have to perform further development-testing with (/based on) the real components you have in hand for such . . . before attempting to integrate it to any larger application !!!

[Eop]

Random

some tests ...

an attempt to get this thing to work at 1.2V . . . the lesser the resistances the greater the speed the more narrow the operating range (resistor = current regulator) , the higher the voltage the faster the qircuit the more sensible a decision to buy the commercial stuff (muhahaa) ↑↑

 how to amplitude limit the above the kHz sine wave ↑↑

[Eop]

Re SCS(SCR) Counter

extends the post http://chpsndtch.blogspot.com/2014/11/scs-counter-sw-d-capacitor-led-single.html

probing the switching modes ::

an attempt to extend down the supply range ::

likely an impractical success ::

... Let's put some sh­¡t up e.g. the weird science about MEM and SCS/SCR

What's good about the Blogger if you dont blog , ? yes.

---

(re-)starting with a lot of diodes 1N4148 + 2N3906 , 2N3904

trying 2-def a microbe-hour csc flip-flop ... it's below the lower half of the kHz range

to induce re triggering - takes deviating from std. about 170 Hz operation (amazingly valid for full possible supply range ???)

---

teh prev. "defined" crash-ware (oldies)

Bench for a single stage ~ about 30kHz op.-s

. . . . . . . . . i finally get this memory cell working . . . . . . . . . 20kHz write (with ultra cool power draw) . . . WHAT WAS UPLOADED WAS 2048x1512px133KB(136733bytes) WHAT YOU ARE LOOKING AT IS 1600x1181px263KB(268929bytes) ??? -- SORRY I GOT IT WRONG AGAIN SO GOOGLE HAD TO "FIX" IT - g.d. perverts - they just can't leave anything untouched . . . . . . ok, (it's just) yet another totally unnecessary "optimization" by Google ________ come on it's just a few lines to add to your server code (run 1-ce(onece) per img. upload) to tell whether you managed to increase 1-st - the i-net bit traffic on each(every) future page request 2-nd - thus everyone elses' wait time (making i-net slowwer)  . . .ok that's about how fast we runn off the fossil fuels , but  ? what i suppose to do ? chk each time if my img.-s're ok ?? and if not  ? split'em into smaller frames ,  ? write extra code for each frame  ? (uploading 4 images (3 extra file headers) instead of 1) ???? delete the "not successful" upload from "blogger album" (takes to wait all blog images to load b4 you can delete any particular 1 OR navigate from 1-st to requred to delete 1) - in "one word" make a day full of job out of what should've taken 2 minutes why i always have to take a day free to uplaod single image - IT JUST SO ABSURD AS IT IS  . . . sorry i don't need to purpose my salary to figure out another "virtual task" - i don't get your game to be honest (perhaps you're just stupid or smth. out of my reach)

---

this is not a ready to use stuff
a snapshots from on going research dev.
it's like @ this Z-up  the grid does THAT
[eof]